Differences

This shows you the differences between two versions of the page.

--- blog:ex475_with_fedora_17 [2012/12/04 00:32] – brett
+++ blog:ex475_with_fedora_17 [2013/05/28 06:48] – brett
@@ Line 1: / Line 1: @@
-====== ex475 with fedora 17 ======
+====== ex475 with Linux (fedora 17) ======
+**You need a video cable for this as it requires a bios tweak**
-I got fed up with trying to figure out how to install WHS2011 onto my ex475.  So I bit the bullet and just installed a linux distribution.
+{{:blog:ex475.jpg }}  I got fed up with trying to figure out how to install WHS2011 onto my ex475.  So I bit the bullet and just installed a linux distribution.
   - Pull bottom drive from your ex475
   - Put drive into spare USB container
-  - Create a VM using VM workstation and point it at a physical disk.
+  - Create a VM using VM workstation and point it at a physical disk (Advanced settings for this)
   - Install Fedora 17.
   - Put drive back and boot it up
@@ Line 22: / Line 23: @@
 </code>
-To resolve the slow disk startup issue required tweaking a BIOS setting (need video cable).
+To resolve the slow disk startup issue required tweaking a BIOS setting.  You'll need video cable http://www.mediasmartserver.net/forums/viewtopic.php?f=6&t=8066 just the bare minimum VGA only will do as keyboard/mouse on USB are fine.
   * Change from 4P(IDE)+4S(RAID)  to 4P(IDE)+4S(IDE)
@@ Line 48: / Line 49: @@
 /dev/sdd1               917G  105G  803G  12% /u04
 </code>
+Same old boring processor.  I never bothered upgrading this.
+<code>
+[root@cheese ~]# cat /proc/cpuinfo
+processor       : 0
+vendor_id       : AuthenticAMD
+cpu family      : 15
+model           : 79
+model name      : AMD Sempron(tm) Processor 3400+
+stepping        : 2
+microcode       : 0x62
+cpu MHz         : 1000.000
+cache size      : 256 KB
+fpu             : yes
+fpu_exception   : yes
+cpuid level     : 1
+wp              : yes
+flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext fxsr_opt rdtscp lm 3dnowext 3dnow up rep_good nopl extd_apicid pni cx16 lahf_lm extapic cr8_legacy
+bogomips        : 1999.88
+TLB size        : 1024 4K pages
+clflush size    : 64
+cache_alignment : 64
+address sizes   : 40 bits physical, 48 bits virtual
+power management: ts fid vid ttp tm stc
+</code>
+The ethernet NIC is working just fine at 1000Mbps
+<code>
+[    7.024358] sis190: sis190 Gigabit Ethernet driver 1.4 loaded
+[    7.024551] sis190 0000:00:04.0: setting latency timer to 64
+[    7.024576] sis190: 0000:00:04.0: Read MAC address from EEPROM
+[    7.042027] sis190: 0000:00:04.0: Atheros PHY transceiver at address 0
+[    7.178369] sis190 0000:00:04.0: eth0: 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at ffffc9000035c000 (IRQ
+: 19), 00:0a:e4:86:6b:83
+[    7.178554] sis190 0000:00:04.0: eth0: RGMII mode.
+[    7.178660] sis190 0000:00:04.0: eth0: Enabling Auto-negotiation
+[   18.728031] sis190 0000:00:04.0: eth0: mii ext = 0000
+[   18.734019] sis190 0000:00:04.0: eth0: mii lpa=c1e1 adv=01e1 exp=000f
+[   18.738022] sis190 0000:00:04.0: eth0: link on 1000 Mbps Full Duplex mode
+</code>
+File transfers are significantly faster than when it was running Windows - I can sustain ~83 MB/s on a 40Gb file.
+{{tag>hardware}}